Electrical Tools For Professionals

• ring LED to provide crimping cycle information and to lighten the workplace
• working trigger with motor stop function at the stroke
• release trigger
• ergonomic handles in bi-component plastic
• handling ring for transportation (strap) or safety cable
• USB connection for data analysis & preventive maintenance
• safety locking trigger
• protection membrane to ventilate the electronics keeping it safe from moisture and dust
• LED display panel for battery charge level, cycle conformity, maintenance
• electronic protection in case of overpressure
• quick motor stop function at cutting end for high user safety
• energy saving function for switching off the tool
• rimping speed improved by a high performance motor
• 2 hydraulic pump stages for improved fast advance
• copper, aluminum and stee calbes/ropes/rods
• max passage up to ø 45 mm
• cutting guillotine type
• locking pin
• interchangeble blades
• rotative heads 220°

• it allows the heads of the BM 200 manual hydraulic multi-head press to be used with pumps

• lateral snap opening for quick and easy die positioning
• the crimping head must be combined with BM 200 manual hydraulic multi-head tool
• it can be combined with a pump using a BM 200CC adapter

• with 86 series dies, it allows aluminum terminal to be crimped through deep indent
• 18694 adapter is required to use the 84 series dies
• with male quick coupling fitting with automatic locking
• for operation it must to be combined with a pump with an operating pressure of 700 bar

Dies made of micro-casted steel.
Cold-pressed steel levers.
Handles insulated with anti-slip plastic.
Equipped with safety device and end-of-work release.

• high pressure flexible tube with quick coupling female connector with automatic locking
• automatic end-of-work release device to guarantee punching quality
• automatic release device at the end of operation
• for operation it needs a 220V power supply

• high pressure flexible tube with quick coupling female connector with automatic locking
• automatic end-of-work release device to guarantee punching quality
• release device activated by a button to open the tool at the end of operation and in case of a wrong maneuver
• for operation it must be connected to an air compressed source of 6-10 bar

Safety device with mechanical end-of-work release ensuring correct crimping.
Possibility of cutting and stripping the cable.
Ergonomic handle in bi-component material.

Product Details:

Application:

• The maintenance-free level switch is used for monitoring the level of liquids in open or closed, pressure less tanks.
• It is nearly insensitive to external interferences and resistant to non-flammable hydraulic liquids.

Construction and Function:

• The inserted permanent magnet in the float actuates contact less bistable dry reed contacts. The contacts are fitted on a rail inside the float guide tube, marked in cm an are adjustable in high (min. space of the contacts min. 90 mm). After release of the adapter sleeve a fine-adjustment is also possible. At pushing forward of the immersion tube in a longitudinal equally.
• By turning the contacts for 180° each can be converted from a normally open contact to a normally closed contact or vice versa. For a tank with turbulent flow a smoothing pipe for the float can be delivered if requested. If requested a thermo-contact to monitor the flow temperature can be mounted. 

Product Details:

We are leading manufacturers and suppliers of Insulated Tool Kits for Electrical Professionals, which serves their purpose in entirety. We provide these in a red tool case inclusive of engineer pliers, side cutters, telephone pliers, long round nosed pliers and a round cable cutter. It is a comprehensive kit. All tool handles comprise of an outer insulating layer and an inner insulating layer to prevent wear.

Product Details:

Product Categorymechanical drillersForce55 kNPuncher diesT series, Q series and R seriesPunch connection threadM16 x 1.5Maximum punching dimensions• round punching: 72 mm (48 mm for inox)
• square punching: 68 mm x 68 mm
• rectangular punching: 46 mm x 92 mmMaximum punching thickness• iron sheet: max 3 mm
• ASI inox 304 steel sheet: max 2 mm
• aluminum and plastic material: max 5 mmHow to use• make the hole on the sheet with the drill
• pass the guide pin through the pre-drilled hole
• assembly the die and the punch on both sides of the sheet
• perform the punchingcid31AC04A

PDF documents

Product CategorypunchersCompatibility• BM 185, BM 1856 (manual hydraulic punching tools) for side up to 68 mm
• BM 200F (punching head for BM 200 manual hydraulic multi-head) for side up to 68 mm
• BM 265 (punching head for pump)Materialcemented steelcid31AC05C

• tool with wide opening that allows for drilling in the corners, even if there are edges
• cast aluminum body and handle make the device very light
• regrindable and interchangeable hardened steel punch
Applications: fastening and joining of cable ducts, drilling for rivets, etc.
Not suitable for stainless steel.

High-precision sharpened, hardened steel tool, that requires minimal effort thanks to the optimal leverage of the handles and the shape of the blades.

High-precision sharpened, hardened steel tool, that requires minimal effort thanks to the optimal leverage of the handles and the shape of the blades.

Product CategorypinsMaterialcemented steelPin threadM16 x 1.5cid31AC05F

Product CategorypinsMaterialcemented steelPin threadM16 x 1.5cid31AC05E

• tool with wide opening that allows for drilling in the corners, even if there are edges
• cast aluminum body and handle make the device very light
• regrindable and interchangeable hardened steel punch
Applications: fastening and joining of cable ducts, drilling for rivets, etc.
Not suitable for stainless steel.

• closed guillotine cut
• protections on the guillotine sides
• for operation it must be combined with a pump with an operating pressure of 700 bar

Empty case for CRIMPAR crimping tool and 5 dies + screws for quick replacement of dies